Close



Page 1 of 2 12 LastLast
Results 1 to 25 of 43
  1. #1

    Default 87-up stock brakes, spindles, UPR caster camber plates

    Nice clean parts of my 85, I'm going to bigger brakes. Rotors and pads only 300 miles.
    Calipers w/pads and caliper bolts- $50 pair
    rotors with inner/outer bearings-$40 pair
    UPR C/C plates- $50
    87 spindles-$80
    drums $20 pair
    flaming river steering shaft $75
    Box of used pads/shoes-$20
    Nitto 275/40/17 drag radials -$100 NT555R

    Strange 31 spline as/street axles with strange c-clip eliminators installed -$200 SOLD
    I forgot to add that buyer pays shipping charges.

    MAKE OFFER
    Attached Images Attached Images      
    Last edited by Hammer Down; 09-28-2018 at 03:48 PM.

  2. #2
    FEP Super Member
    Join Date
    May 2003
    Location
    Roseburg Oregon
    Posts
    3,308

    Default

    Where are you located ?
    clowns to the left of me , Jokers to the right

  3. #3

    Default

    Location (city and state) required

  4. #4

    Default

    Sorry. I'm near Detroit mi. 48357 . The only reason I pulled this stuff is because I'm building a HPDE car and am going five lug with 13" cobra brakes. I also have clean nice front backing plates. I will also be pulling the rear end apart soon and have nice 31 spline axles and the drum brake setup with maximum motorsports shoes. I also will have a nice MC and nice front rubber brake lines. And I have several sets of front wheel bearings and a set of Hawk front pads.
    Last edited by Hammer Down; 08-01-2018 at 06:39 AM.

  5. #5

    Default

    So are the spindles for the 10in or 11in rotor?

    Sent from my SM-G950U using Tapatalk

  6. #6

    Default

    11" I believe they are out off a Turbocoupe.

  7. #7

    Default

    I’m interested in the calipers, rotors, CC plates, MC and soft lines. Shipping zip is 47006. PM me a price when you get a chance. I already bought spindles- should have waited!

  8. #8

    Default

    Quote Originally Posted by GT Town View Post
    I’m interested in the calipers, rotors, CC plates, MC and soft lines. Shipping zip is 47006. PM me a price when you get a chance. I already bought spindles- should have waited!
    Ok. I'll get back to you tonight. I still have to pull the soft lines and MC.

  9. #9

    Default

    MC and lines
    Attached Images Attached Images   

  10. #10

    Default

    31 spline axles, drum brake setup with maximum motorsport shoes, backing plates, for sale also. The axles are c clip eliminator fox length(not sure if that makes a difference).
    Attached Images Attached Images     

  11. #11
    FEP Member
    Join Date
    Jan 2016
    Location
    South Central Ohio
    Posts
    111

    Default

    Caster/camber plates still available?

  12. #12

    Default

    Quote Originally Posted by 85WhiteGT View Post
    Caster/camber plates still available?
    They might be sold. If not I will let you know.

  13. #13

    Default

    Axle pics
    Attached Images Attached Images    

  14. #14
    FEP Member
    Join Date
    Jan 2016
    Location
    South Central Ohio
    Posts
    111

    Default

    Quote Originally Posted by Hammer Down View Post
    They might be sold. If not I will let you know.
    Ok, Thanks, just let me know.

  15. #15

    Default

    Quote Originally Posted by 85WhiteGT View Post
    Ok, Thanks, just let me know.
    If I don't hear from the other guy in a day or so the plates are yours.

  16. #16

    Default

    Flaming river steering shaft. The other knuckle says made in Kalamazoo mi. I just painted it, too, while I was painting my new one. $75 plus shipping. Please, if anyone is interested in any of these parts, make me an offer. I want to move this stuff.
    Attached Images Attached Images   

  17. #17

    Default

    275/40/17 NT555R Extreme Drag Radial
    Attached Images Attached Images    

  18. #18

    Default

    Sway bar mounts/bushings
    Attached Images Attached Images  

  19. #19

    Default

    I still have all this stuff. I also have a QA1 adjustable tie rod kit, a NOS set of 94-95 SN95 spindles with hubs and studs(never been on a car). Sway bar links.

  20. #20
    FEP Power Member STL79Coupe's Avatar
    Join Date
    Dec 2009
    Location
    St. louis MO
    Posts
    2,464

    Default

    Quote Originally Posted by Hammer Down View Post
    I still have all this stuff. I also have a QA1 adjustable tie rod kit, a NOS set of 94-95 SN95 spindles with hubs and studs(never been on a car). Sway bar links.
    How much for the 94-95 spindles? Is the steering shaft for manual steering? Thanks
    Keith formerly STLPONDS
    '79 V8 coupe in the works!
    Build thread http://vb.foureyedpride.com/showthread.php?t=89153

  21. #21

    Default

    Asking $300 for the spindles/hubs assembly(new studs also). The steering shaft is for a stock 85 power rack.

  22. #22

    Default

    Do you still have the 87 spindles? Shipping to 76011?

  23. #23

    Default

    Quote Originally Posted by hcmclean View Post
    Do you still have the 87 spindles? Shipping to 76011?
    I still have them. I'll check on the shipping

  24. #24

    Default

    Thanks.

  25. #25
    FEP Member brianj's Avatar
    Join Date
    Feb 2012
    Location
    Raymond, New Hampshire
    Posts
    2,896
    Blog Entries
    2

    Default

    I'm curious what you're getting for shipping quotes. I'd like all of the front brake parts, but i think shipping 75 pounds of iron to New Hampsire would be really pricey.
    1983 Mustang G.T. No-option stripper- I like strippers.
    5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •