Looks Great!
Now for the fun of making both sides match!
Trey
Looks Great!
Now for the fun of making both sides match!
Trey
Trey
"I Don't build it hoping for your approval! I built it because it meets mine!"
"I've spent most of my money on Mustangs, racing, and women... the rest I just wasted."
Mustangs Past: Too many to remember!
Current Mustangs:
1969 Mach 1
1979 Pace Car now 5.0/5 speed
1982 GT Stalled RestoModification
1984 SVO Still Waiting Restoration
1986 GT Under going Wide Body Conversion Currently
Current Capris:
1981 Capri Roller
1981 Capri Black Magic Roller Basket Case
1982 Capri RS 5.0/4spd T-top Full Restoration Stalled in TX
1984 Capri RS T-top Roller
1983-84 Gloy Racing Trans Am/IMSA Body Parts
Been there, done that. Not fun. As I cut and fit the first side, I cut and ground the second side pieces at the same time. Not a guarantee, but it helps. What I am not looking forward to is getting all of these welds and edges straight, and keeping the body lines crisp on the new pieces. I then have to rip it all back off, coat the back, jamb the car, re install them with seam sealer, and hope it all still lines up.Originally Posted by wraithracing
Looks Great!
Now for the fun of making both sides match!
Trey
Last edited by brianj; 11-16-2013 at 06:02 PM.
1983 Mustang G.T. No-option stripper- I like strippers.
5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.
You could probably make some SVO style spats with less difficulty. I bet folks would buy them if they were available.
Jess
Previously owned;
1979 Mustang, v6 swapped to EFI 393, custom installed m122 blower, 4r70w trans, Megasquirt II, T-top swaped in.
1990 Mustang, 545 BBF, C-4 with brake, ladder bars.
1983 Mustang, 1984 SVO Mustang
1984 Mustang convertible, v6 swapped to 351
1986 Mustang GT, 1989 Mustang GT convertible
1992 Mustang coupe, 4 swapped to 302
Yes, those are easy. I wanted something that looked less "stuck on". However, if people were interested, I could whip those out pretty simply.
1983 Mustang G.T. No-option stripper- I like strippers.
5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.
That's a good way to do it to help things match. I know in my experience that getting both sides identical is always the most frustrating, so I feel your pain!
Just keep in mind how awesome it will look when you get it all done and painted and that will keep you motivated to get it all done!
Trey
Trey
"I Don't build it hoping for your approval! I built it because it meets mine!"
"I've spent most of my money on Mustangs, racing, and women... the rest I just wasted."
Mustangs Past: Too many to remember!
Current Mustangs:
1969 Mach 1
1979 Pace Car now 5.0/5 speed
1982 GT Stalled RestoModification
1984 SVO Still Waiting Restoration
1986 GT Under going Wide Body Conversion Currently
Current Capris:
1981 Capri Roller
1981 Capri Black Magic Roller Basket Case
1982 Capri RS 5.0/4spd T-top Full Restoration Stalled in TX
1984 Capri RS T-top Roller
1983-84 Gloy Racing Trans Am/IMSA Body Parts
Not to steal work from Brian if he wants it, but the SVO style spats are reproduced in fiberglass.
Here is a link to them. http://www.svpu.com/ccart/index.php?...&product_id=47
Trey
Trey
"I Don't build it hoping for your approval! I built it because it meets mine!"
"I've spent most of my money on Mustangs, racing, and women... the rest I just wasted."
Mustangs Past: Too many to remember!
Current Mustangs:
1969 Mach 1
1979 Pace Car now 5.0/5 speed
1982 GT Stalled RestoModification
1984 SVO Still Waiting Restoration
1986 GT Under going Wide Body Conversion Currently
Current Capris:
1981 Capri Roller
1981 Capri Black Magic Roller Basket Case
1982 Capri RS 5.0/4spd T-top Full Restoration Stalled in TX
1984 Capri RS T-top Roller
1983-84 Gloy Racing Trans Am/IMSA Body Parts
Ahh, but I could make them for cars that do not have the rocker moldings!
1983 Mustang G.T. No-option stripper- I like strippers.
5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.
Steel ones could be welded on and blended in real nice.
Jess
Previously owned;
1979 Mustang, v6 swapped to EFI 393, custom installed m122 blower, 4r70w trans, Megasquirt II, T-top swaped in.
1990 Mustang, 545 BBF, C-4 with brake, ladder bars.
1983 Mustang, 1984 SVO Mustang
1984 Mustang convertible, v6 swapped to 351
1986 Mustang GT, 1989 Mustang GT convertible
1992 Mustang coupe, 4 swapped to 302
Got a little more done, although not nearly what I wanted. I got called in to work to save the world from squirrels (long story) and my MIG crapped out. But at least it is better than nothing.
1983 Mustang G.T. No-option stripper- I like strippers.
5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.
I would install those large fogs like the bug eye impreza and 2.5 rs came with. Maybe some small canards.
Brian, how much weight do you figure your adding to the car?
Dave
If common sense was common wouldn't it just be sense?
1983 Capri L T top 5.0 efi aod
1983 Capri RS Turbo
1981 Black Magic 400 c6
93 F-250 351 5sp 4x4
A full 4x8 sheet of 22GA steel is around 30LB. 60' of 1/8×1/2 strip and 60' of 1"×1/8 was 42LB. Minus the scrap, plus the body filler, probably around 70LB. for the whole thing.
1983 Mustang G.T. No-option stripper- I like strippers.
5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.
Nice! The weights not bad either. Hell that's about the weight savings of a K-Member.
Yep, or removing the jack and spare. I swore I had, and when I pulled out the interior, I had not. I wish I had gotten a couple of runs in without the jack, spare, and rear seat, with drag radials. Bet I would have hit twelves.
1983 Mustang G.T. No-option stripper- I like strippers.
5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.
Not bad. You're doing an awesome job as well.
Dave
If common sense was common wouldn't it just be sense?
1983 Capri L T top 5.0 efi aod
1983 Capri RS Turbo
1981 Black Magic 400 c6
93 F-250 351 5sp 4x4
Wow, Brian, great work! I wish I was there to see it (kinda). You'll have to take it on a short drive down 95 to visit when it's done!
Looks great Brian. That has to be a good feeling knowing you are doing that yourself.
Love it man. Wished I could do this kinda stuff. I think the front would look even more sweet if it had more of a splitter look kinda like the cobra splitter. I mean with just that little piece added to the very bottom to make it stick out.
Been working a ton with the bad weather around here- It has been difficult to get anything done. I did get the last side skirt finished.
I have the framework for the rear valance roughed in. Not sure I am in love with it, but I will have to see. It is hard to capture how it looks in a picture, since it is so two dimensional, but you get the idea. It follows the line of the bumper cover exactly.
Last edited by brianj; 11-27-2013 at 08:28 PM.
1983 Mustang G.T. No-option stripper- I like strippers.
5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.
Getting there. It is a little easier to see what it looks like like this.
1983 Mustang G.T. No-option stripper- I like strippers.
5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.
looks great, keep us updated.
Looking pretty cool!
Trey
Trey
"I Don't build it hoping for your approval! I built it because it meets mine!"
"I've spent most of my money on Mustangs, racing, and women... the rest I just wasted."
Mustangs Past: Too many to remember!
Current Mustangs:
1969 Mach 1
1979 Pace Car now 5.0/5 speed
1982 GT Stalled RestoModification
1984 SVO Still Waiting Restoration
1986 GT Under going Wide Body Conversion Currently
Current Capris:
1981 Capri Roller
1981 Capri Black Magic Roller Basket Case
1982 Capri RS 5.0/4spd T-top Full Restoration Stalled in TX
1984 Capri RS T-top Roller
1983-84 Gloy Racing Trans Am/IMSA Body Parts
Keep those pictures coming! Very interesting!
1982 Dominator GT
*1st Dominator ever sold and
autographed by Jackie Stewart *
1993 Corvette
2005 Roush Mustang
2008 Escape (DD)
Rear is done. Now I have to finish the front.
1983 Mustang G.T. No-option stripper- I like strippers.
5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.
Looks great, keep going!
Posting Permissions
Reply With Quote
Connect With Us