Close



Page 18 of 18 FirstFirst ... 8161718
Results 426 to 427 of 427
  1. #426
    FEP Super Member xctasy's Avatar
    Join Date
    Jun 2012
    Location
    Dunedin 9011, New Zealand, South Pacific
    Posts
    2,984

    Default

    http://vb.foureyedpride.com/showthre...27#post1871727

    Please check with and PM http://vb.foureyedpride.com/search.php?searchid=1074128.

    Ask Roger (behind the Dark Red car , white shirt no jacket, was a fuel engineer)

    The dark red Mercury Capri

    http://vb.foureyedpride.com/showthre...k-for-Fox-Cars


    There was another power-train engineer who discussed the turbo 2.3 gearbox development and vibration and noise updates last year. Those guys normally hang out with certifications, so they have access to development info.

    An earlier non EFi fuel engineer will help you out.

    Blue86's

    http://www.foureyedpride.com/content...inner-Blue86-s

    http://vb.foureyedpride.com/member.php?4633-Blue86
    His dad is a retired Ford engineer as well. He worked at Ford for forty years. In the eighties he worked in engine development and SVO.

  2. #427

    Default

    Ok so a few more hours in and we are 90% through the vacuum line tracing/fixing. I've added the two lines for the A/C side (right) SOLV and part of the anti-backfire device as well as completed the A/CL BI MET lines. She is idling and running very well and spools great except for now after the other vacuum fixes I have a concerning carb backfire/poof with a cloud of black smoke when on full throttle and I put the clutch in to shift gears (so much for adding in the anti-backfire device!). If I make very slow shifts it's no problem. This is no buenos and must be fixed so I won't do any further full pulls. I'm sourcing the missing A/CL TVS from National Parts Depot so I can fully connect the AIR BPV/ANTI BF system which I hope will solve this issue as I don't want to blow up the turbo carbon seal. I am doubtful but may play with the timing again in the meantime.

    My AFR gauge still does not read at idle by wiring directly to battery so I think it needs to be replaced in order to trust the readings for fine tuning.

    I do not see the FLTR that connects to the AIR BPV in my engine compartment as that upper port is closed. Does anyone know what it's function is and have a picture of said FLTR?

    Finally this is the Vacuum Control Valve right?

    This pic is my old setup with lower VCV port going to the IVV and the other to the air port next to the primary carb mixture screw. The IVV lines are now fixed per the VECI diagram (to small A/CL CWM port and to the formerly open EGR port) but the VCV lower port is now open which is supposed to go to the E port on the carb with a SA FV which I also don't have). It is supposed to go to a tee then to the VDV then to the purge canister center line which is also open at the moment. Looks like I need to source a VDV and SA-FV in order to finalize all of this.

    Lastly I have a large vacuum line (turquoise stripe) running from the firewall RT corner area to the large A/CL CWM port but I can't ID this Line on the VECI. Anyone know what this does? Does the stripe designate something specific? At the split valve one goes in the firewall behind the glove box somewhere while the other one disappears behind the fender.


    Here's my Purge CV with middle orange?/pink? (it splits into two lines not sure why as the VECI only shows as single line; same thing on the Left SOLV lines where both split into two then back to one...strange) that needs to route to VCV.
    [/url]
    Last edited by m81mclaren; 02-12-2019 at 02:47 AM.
    Current FEP:
    1980 M81 McLaren Carb Turbo 2.3T #003P ... IT'S ALIVE after a 22 year slumber thread!

    Past FEP:
    1986 Capri GS 5.0- very missed but in goods hands
    1985 LTD SSP- quick little fox 5.0

Page 18 of 18 FirstFirst ... 8161718

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •