Hey guys, went to replace my sway bar end links and bushings today and noticed that my sway brackets are toast lol. What brackets do you all recommended are good to replace them?
Attachment 123661
Hey guys, went to replace my sway bar end links and bushings today and noticed that my sway brackets are toast lol. What brackets do you all recommended are good to replace them?
Attachment 123661
Last edited by Sask84gt; 09-09-2018 at 10:12 PM.
Unless those brackets are supposed to be bent like that? In that case I would sandblast and re use
Not supposed to be like that. Did you change a-arms?
Most likely the sway bar was used at one point to pull the car onto a trailer or tow it. Happens all the time as it is an easy location to attach a tow strap or chain to. Same reason so many lower core supports are damaged in these cars.
Essentially any sway bar bracket from 79-93 can be made to work. It is often easiest to find the 87-93 brackets just because so many are still out there and many get converted to drag cars and ditch the front bar. The SVO brackets are slightly different, so I don't recommend those.
Honestly yours are not that bad. You could try straightening them and most likely be able to reuse them. Here is a link to a set on Ebay for reference or if you would rather replace them. Good Luck!
https://www.ebay.com/itm/1987-1993-M...MAAOSwEW9ahOjn
Trey
"I Don't build it hoping for your approval! I built it because it meets mine!"
"I've spent most of my money on Mustangs, racing, and women... the rest I just wasted."
Mustangs Past: Too many to remember!
Current Mustangs:
1969 Mach 1
1979 Pace Car now 5.0/5 speed
1982 GT Stalled RestoModification
1984 SVO Still Waiting Restoration
1986 GT Under going Wide Body Conversion Currently
Current Capris:
1981 Capri Roller
1981 Capri Black Magic Roller Basket Case
1982 Capri RS 5.0/4spd T-top Full Restoration Stalled in TX
1984 Capri RS T-top Roller
1983-84 Gloy Racing Trans Am/IMSA Body Parts
Ok thanks Trey, I will see if I can fix em first. Are the prothane ones that lmr sell any good? Kind of confused if those are stock replacements or for some kind of conversion?
These ones? First is 1 5/16, second link is 1 1/8
https://lmr.com/item/PT-191138BL/Mus...ushing-for-Mm-
https://lmr.com/item/PT-191136BL/mus...-1-8-inch-7993
Also I just measured my stock sway bar with calipers and it measured 1.283. I'm assuming that I have the 1 5/16 sway bar?
Last edited by Sask84gt; 09-10-2018 at 08:26 AM.
Well they look better than before lol.
Attachment 123708
Edit: sorry for the sideways pic. not sure why it keeps happening.
Here is final piece with sway bar that was sandblasted and painted. Turned out not bad for a rookie lol
Attachment 123709
The Prothane mounts can work, but they don't lower the bar as much as the OEM units which can cause clearance issues sometimes at the oil pan.
Mounts look much better. I generally measure my swaybar using a large open end wrench. Most 4 Eyes have either an 1 1/8 or 1 5/16 front bar so that makes it quick and easy to verify in most cases. The SVO front bar is 1.20 or just under 1 1/4" if you have one of those.
I use Prothane or Energy Suspension Poly Urethane bushings for most of my vehicles both work just fine. Good Luck!
Trey
"I Don't build it hoping for your approval! I built it because it meets mine!"
"I've spent most of my money on Mustangs, racing, and women... the rest I just wasted."
Mustangs Past: Too many to remember!
Current Mustangs:
1969 Mach 1
1979 Pace Car now 5.0/5 speed
1982 GT Stalled RestoModification
1984 SVO Still Waiting Restoration
1986 GT Under going Wide Body Conversion Currently
Current Capris:
1981 Capri Roller
1981 Capri Black Magic Roller Basket Case
1982 Capri RS 5.0/4spd T-top Full Restoration Stalled in TX
1984 Capri RS T-top Roller
1983-84 Gloy Racing Trans Am/IMSA Body Parts
Thanks! Also is there a measurement to go off when putting bar back on? Where should the brackets sit on the sway bar?
Just make sure to get a good film of grease on that bar and inside the bushings. Your ears will thankyou
Trey
"I Don't build it hoping for your approval! I built it because it meets mine!"
"I've spent most of my money on Mustangs, racing, and women... the rest I just wasted."
Mustangs Past: Too many to remember!
Current Mustangs:
1969 Mach 1
1979 Pace Car now 5.0/5 speed
1982 GT Stalled RestoModification
1984 SVO Still Waiting Restoration
1986 GT Under going Wide Body Conversion Currently
Current Capris:
1981 Capri Roller
1981 Capri Black Magic Roller Basket Case
1982 Capri RS 5.0/4spd T-top Full Restoration Stalled in TX
1984 Capri RS T-top Roller
1983-84 Gloy Racing Trans Am/IMSA Body Parts
I like a silicone grease on poly, but bearing grease would work too. I always used that when I changed rubber ones in the shop. Something to cut the squeaking
Connect With Us