Close



Results 1 to 5 of 5
  1. #1

    Default Ripped the band-aid and a little bit of science with exhaust...

    Well, I had a rear main seal go and while the guys were fixing that I said "Hey, while you have it all torn up, why not toss these brand new Hooker 6128hkr super comp shorty equal length headers I have had sitting in the garage for 2 years on there?". They said, "Sure! Why not?".

    So, I finally modified my untouched g.t. 350. But here is where the contribution to understanding the engine comes in... I had them touch nothing else. Exact same engine, exact same exhaust (all smog gear intact), exact same header pipe (they modified the attachment to the headers to make it work).

    So what happens when you just get rid of the old exhaust manifolds on an 84.5 convertible 5.0 anni with CFI and an automatic? Well, the headers fit (they swore a lot, or so they tell me) but they fit. At least these fit. Down low off of a start not much changed. Sounds a bit more more 'throaty' but with a big old muffler on a single exhaust I didn't expect too much.

    When you get up into the 2k+ range I start to feel the difference. The car at high RPM now surges rather than feels 'held back'. It's not crazy but it no longer feels hobbled. Climbing slope at forty and flooring it used to result in lots of noise but not a whole lot of acceleration. Now it is a throatier noise and some real acceleration. At highway speeds (50 and up) the car is responsive and accelerates without the kind of effort it had before.

    I am sure it would do all of this even more so with dual exhaust or perhaps minus the 33 year old cat but that is not the point. yet,

    So, there you go. What happens when you just swap out the headers. Like I said though, the guys that did it (seasoned mechanics) said it sucked bad. However...


    Next project will be the intake manifold. I don't expect much there but since I have ripped that band-aid, why not...Name:  1ho.jpg
Views: 110
Size:  102.5 KB
    Name:  2ho.jpg
Views: 111
Size:  97.7 KB
    Name:  3ho.jpg
Views: 111
Size:  106.7 KB
    Last edited by emerygt350; 08-28-2017 at 06:54 PM.

  2. #2

    Default

    Good, Good, let the modifications flow through you. Feel the force of the added power.

    Jess
    Currently own;
    1979 Mustang, v6 swapped to EFI 393, custom installed m122 blower, 4r70w trans, Megasquirt II, T-top swaped in.
    Previously owned;
    1990 Mustang, 545 BBF, C-4 with brake, ladder bars.
    1983 Mustang, 1984 SVO Mustang
    1984 Mustang convertible, v6 swapped to 351
    1986 Mustang GT, 1989 Mustang GT convertible
    1992 Mustang coupe, 4 swapped to 302

  3. #3
    FEP Member brianj's Avatar
    Join Date
    Feb 2012
    Location
    Raymond, New Hampshire
    Posts
    2,725
    Blog Entries
    2

    Default

    Lol. Once you start, good luck. You're screwed.
    1983 Mustang G.T. No-option stripper- I like strippers.
    5.0, GT40P heads, Comp Cams XE270HR-12 on 1.6 rockers, TFI spring kit, Weiand 174 blower, Holley 750 mechanical secondarys, Mishimoto radiator, Edelbrock street performer mechanical pump, BBK shortys, T-5 conversion, 8.8 rear, 3.73 gears, carbon fiber clutches, SS Machine lowers, Maximum Motorsport XL subframes, "B" springs.

  4. #4

    Default

    Quote Originally Posted by brianj View Post
    Lol. Once you start, good luck. You're screwed.

    Yeah, I know. All of the online ads are now showing an edelbrock 3723 and fan clutch kits.

    Gonna have the duals done next though. Some time this winter...

  5. #5
    FEP Senior Member Matt J's Avatar
    Join Date
    Jul 2012
    Location
    Georgia
    Posts
    505

    Default

    Hey, it's all bolt-on stuff. If you really want to keep the original stuff in the event that someday someone will really want it, go ahead. The car will be better to drive with the upgrades, and that's really why you own it, right?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •