Close



Results 1 to 11 of 11
  1. #1

    Default Pcm where there wasnt

    Who has put a pcm into the right kick panel where there wasn't one. Looking for advice or experience in doing so. Pics are a plus. Thanks

  2. #2

    Default

    AFAIK the sheetmetal is slightly different over there on the 86-93 cars. I don't have pictures of my 86 anywhere but I seem to remember seeing something about that in an article once.


    I suspect pictures of yours and also of an 86+ would help you.

  3. #3

    Default

    Yes it appears my 79 is different compared to the 87 I have. That's why I'm looking for what someone else may have done. I'll get it done, just thought if someone else has done it, it might make it easier

  4. #4

    Default

    That's a problem I still haven't solved on mine. It's just hanging there. I've considered buying an extension harness. There's a guy that makes them on ebay, but his prices are WAY high. Around $300. I've heard from a guy I know, you can extend the wires yourself, just make sure to shield and ground the ones that need it. That sounds a little scary to me though, haha.
    Brad

    '79 Mercury Zephyr ES 5.0L GT40 EFI T-5 (Mustang LWB)
    '17 Ford Transit Connect Titanium LWB
    '14 Ford Fusion SE Manual

  5. #5

    Default

    Shrink tubes and solder. One wire at a time should work fine.

  6. #6

    Default

    ...buuuut then where do you put it.

  7. #7

    Default

    Get out the plasma cutter..... it'll be fine.

  8. #8
    FEP Super Member mustangxtreme's Avatar
    Join Date
    Feb 2009
    Location
    Snohomish, Wa
    Posts
    3,954

    Default

    I put mine between the kick panel and heater. It is a tight fit but, I've been driving it like that for years.
    Dave

    If common sense was common wouldn't it just be sense?

    1983 Capri L T top 5.0 efi aod
    1983 Capri RS Turbo
    1981 Black Magic 400 c6
    93 F-250 351 5sp 4x4

  9. #9
    Moderator wraithracing's Avatar
    Join Date
    Jun 2010
    Location
    Grand Junction, CO
    Posts
    10,904

    Default

    I have not tackled this on my 82 GT yet either, but will need to.

    I did actually place the Huge Fuse panel from a Ron Francis Wire Works wiring kit in the passenger kick panel or maybe more accurately ON it. I then modified the kick panel plastic trim piece to cover it. Basically lost some leg room down there for the passenger, but was much easier and simpler than modifying the sheetmetal at the time.

    I am still down in TX working but I will try and get some pictures when I get back to CO. Good Luck!
    ​Trey

    "I Don't build it hoping for your approval! I built it because it meets mine!"

    "I've spent most of my money on Mustangs, racing, and women... the rest I just wasted."

    Mustangs Past: Too many to remember!
    Current Mustangs:
    1969 Mach 1
    1979 Pace Car now 5.0/5 speed
    1982 GT Awaiting Restoration
    1984 SVO Restoration in Progress
    1986 GT Wrecked by PO, but still want to save!

    Current Capris:
    1982 Capri Roller
    1984 Capri Returned to Bubble Back Glory
    1983-84 Gloy Racing Trans Am/IMSA Body Parts

  10. #10

    Default

    Quote Originally Posted by erratic50 View Post
    Shrink tubes and solder. One wire at a time should work fine.
    Yeah, but don't some need to be "shielded" or whatever?
    Brad

    '79 Mercury Zephyr ES 5.0L GT40 EFI T-5 (Mustang LWB)
    '17 Ford Transit Connect Titanium LWB
    '14 Ford Fusion SE Manual

  11. #11

    Default

    Speed sensor wires are twisted, and there is a spec for that. I have come to the opinion that it just isnt worth the structural damage to go into the kick panel. The early ones are too different. It will go on a tray I make and hang flat under the hvac box. If I lengthen the harness maybe it would lay nicely under the dash where the radio is. Last option though if my way takes too much foot room.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •