Close



Page 3 of 3 FirstFirst 123
Results 51 to 61 of 61
  1. #51

    Default

    A lot has been happening but it seems like progress is SLOW. And Sydney's birthday is a little more than a week away. It's clear we won't make it with a running car for her birthday, especially since we're headed to Charleston for a vacation and eclipse viewing.

    First up are wheels. It's time for the car to leave the lift so that we can work on the interior and wiring. Needs wheels to do that so I bolted on a set of the Chump Cobra knockoffs which have the same common offset and backspacing as most all 17" factory Ford wheels (~5.95" backspace, 24mm offset). The problem is that on the front, with the SN95 LCA, the wheel sticks out about 1/2" outside the fender. A lot of camber can barely tuck it up under the fender.





    So, either I use some asymmetric wheels (rear fits fit with normal wheels) or I go back to a fox arm. I'm going with the fox arm, which means we have to fab up a new pair of arms with weight jackers and press the bushings I want to use into the arms. At least we'll have a spare set of LCAs for the SN95 race cars. I've already sand blasted the fox arms and we've taken the existing suspension off the car.





    How long as it been since you've seen a round air filter? Long time for me and it brought back a lot of memories of working on older Fords.



    I forgot to put some detail in on the radiator and fan. There I bought a fox 3 core ally radiator and I wanted to use an electric fan, specifically a Ford OEM fan. We've got a lot of e fans lying around so I chose a SN95 94-95 style fan as it fit really well on the radiator. All we had to do was fab up some ally supports and weld them to the radiator. I suck at ally welding but we were able to get it done well enough to work for the setup. Most of the fan weight is carried by the fan lip resting on the bottom of the radiator, but even without that the mounts are sturdy although not pretty.





    Since electrics are going in I needed a battery in place to fabricate the heavy current harnesses. I've got that in place now and it's tidy, down to the starter, grounds, and some feeds for the fuse panel.



    First job was to locate the Ron Francis fuse panel. That was done by fabbing up a few cardboard templates and trying them in various locations in the car up behind the dash and where the panel would still be accessible.



    Once we had a good location we fabbed the mount from steel and installed rivnuts in it that we could use to bolt the fuse panel to the mount.





    And this is mocked up again with the mount and panel where it will live.



    On other fronts, I secured a set of SVO seats that are in decent shape. They need to be recovered but at least I've got the basics in place, complete with manual pump up bladders for lumbar that work well. The gray will match the interior quite well.



    The dash is starting to get attention too. We had it down for mocking up of the fuse panel mounts and it's time for dash repair to happen.



    And on the ordering parts front I got a 17" spare tire. I hadn't thought about that aspect of the car until I read it on the forum, that is, with the larger Cobra brakes you need a special spare that will clear them. Found one in great shape for a fair price.


  2. #52

    Default

    Nice progress! Your fan mounts look pretty dang nice to me! Way nicer than what I'll end up with.

    Sent from my XT1650 using Tapatalk
    Brad

    '79 Mercury Zephyr ES 5.0L GT40 EFI T-5 (Mustang LWB)
    '17 Ford Transit Connect Titanium LWB
    '14 Ford Fusion SE Manual

  3. #53

    Default

    It has been a busy week so little work on the Mustang. What happened? Five day team meeting at work which knocked me out for the week, followed by family vacation and eclipse viewing, and Sydney got her license. Yep, she's now legal to drive and took her first trip out yesterday to have lunch with a friend. I might be more excited than she is since that means we don't have to ferry her around as much as we were doing. Unfortunately the Fox isn't done yet but the pressure is now on!




    Obligatory eclipse picture from our SC trip.



    Now that our busy late summer is winding down we can get down to business on project Fox. First up is making another set of arms for the car since we didn't like what the SN95 arms were going to require in the way of wheels and fitment. Arms Part Deux.





    Sydney got a bit of welding action in assembling the adjustable spring perches. She did fine with it and overcame her fear of "the sparky things".





    And of course we finally selected the wheels and went with a set of GT/Bullet units, around 2002 vintage. They fit up really well and with some 245s or 255s will be the ticket for this car.





    The arms and the rest of the suspension was bolted on and now we're back to where we were a week or so ago. We've got a roller! She's rolling on some of the Cobra wheels at the moment but at least she is rolling. Need to get it off the lift area so that we can turn attention to the interior and wiring.





    I've ordered a lot of parts - upholstery, new door cards, emblems, wiring sheaths, and lots more. I suspect the next immediate job is to roll out the sound deadener on the interior of the car. Yay, but it has to be done.

  4. #54

    Default

    A labor of love -- an outstanding build. Congratulations!

    Some pieces of advise from someone who has a 15 year old daughter himself and also having personally piloted my four eyed fox every day for 18 years then just for fun the other 7 totaling up around 380K miles..... fix the fox rear suspension!

    1- You can go to softer 4-banger LX springs in back (same as the 93 cobra so listen to ford if nothing else) - you'll get a lot less suspension bind. The pair far nicer with the front springs for a way better ride too

    2 - new shocks and quad shocks are essential. Stock style works great with the above springs

    3 - remove the rear sway bar entirely! The stock LX sport and GT front sway bars are stronger than 93 cobra front and rear combined. The rear bar prevents the rear inside tire from staying hooked then the limited slip helps blow the other one off for you.

    Note: I'm well past stock power on my 86 and I can pull out and turn left with my foot planted on the floor and not so much as kick the backend out! You'll have more HP with those heads but I'm certain can see the point

    4 - if possible add a panhard bar or watts link. They are by far the best upgrade I've seen on a fox. The other items above help but this one completely eliminates the rear snap steer that has taken so many cars and so many lives from us all.

    Best of luck getting this beauty on the road. Thanks for sharing all the pictures, we've really enjoyed them!

  5. #55

    Default

    Glad you like the build and thanks for the wishes.

    Your handling suggestions are spot on from my experiences. We are pretty well versed in how to get Foxes/SN95s to handle and perform as we've been road racing SN95s for years. I've built panhards and trilinks for our race fleet (three Mustangs) and I intended to build one for this car. But, when I evaluated the timing of the build I dropped that off at least for version 1.0 just so I could get it on the road. Fox V1.0 has 175 lb springs in the rear which are pretty soft. The adjustable rear shocks will be set soft and the rear bar will get ditched before hitting the road. All four corners have adjustable ride height to help dial in the corner weighting and we will do a bump steer analysis of the front when final setup and corner weighting is done. Eventually it'll get a better rear suspension design but it'll be winter I suspect before that happens.

    So much to do with it and projects are piling up. My race partner and I have been splitting some time on this car and on our endurance road race car. We finished building the motor for it a few weeks ago and need to get it buttoned up this weekend. We're both instructing at VIR Sept 8th weekend with the Tarheel Sports Car Club and need to have it track ready for a shakedown in preparation for races this fall. In addition my sprint road race car's transmission pooped the bed at Charlotte the weekend before last and I need to get to rebuilding another T5 as the 2018 points season starts in October.

    I need to quit my job so I have time for my hobbies!

  6. #56

    Default

    The offspring spent time putting down some dynamat-like product in the floor of the fox. I used the same stuff in the Torino and while I had no back to back comparisons to judge from I *think* it helped a little. Maybe. Without proper sound frequency measurements, which none of these companies seem to be bothered to do even though you can get good spectrum analyzers for your iPhone, it's a crap shoot.



  7. #57

    Default

    Wheels comparison, Cobra:





    Bullitt/Thrusts:





    I am good with either set of wheels and Sydney is too. I enjoy the look of the Cobras for the styling and edges which match the early Fox well. But I like the Thrusts with the gray that compliments the gray trim of the car and what will be a gray interior.


    Anyhow, I went with the Continental Extreme Contact tires in a 255 size and they are mounted on the Thrusts so the car is going to start life with those wheels. Sydney still wants to call in a favor from a good friend of ours and wheel maker (among many other things) and have a set of 10 hole LX/GT wheels from the 80s replicated in a 17" format.

  8. #58

    Default

    Car looks great with the Bullitts! Great progress here! I love my Extreme Contacts.

    If you're able to get 17" 5-lug 10-holes your fellow 4-eye fans may need some too!
    Brad

    '79 Mercury Zephyr ES 5.0L GT40 EFI T-5 (Mustang LWB)
    '17 Ford Transit Connect Titanium LWB
    '14 Ford Fusion SE Manual

  9. #59

    Default

    It has been a couple of weeks since I have updated the thread. Progress is being made but it is slow going on the wiring. We're chipping away at it but still I reckon we're only about 40% done. But, the hard 40% is done.


    One of the early jobs was the pinout for the gauge cluster. Jeff G. handled that part and make a easy to read diagram for the two connectors. We'll make all new gauge harness based on this and make sure it functions properly.





    Meanwhile I took apart the gauge cluster to make sure everything is functioning. It's in excellent shape and the instrument faces were restored awhile ago. While at this stage I removed the ammeter and applied to decal, step one, in converting it to a voltmeter. After that shut removal and conversion.








    We went down the road of messing with the cluster harness and then stopped, turning attention instead to the engine harness and Sniper rig, as well as the fuse panel mounting. Step one was mounting the Ron Francis panel in its permanent location, under the dash left hand side.








    Once it was positioned I could mock the steering column up for mounting the switch and putting the all new harness in for that - switch, power feeds to the panel, clutch switch, AC wiring, fan wiring, brake, etc.





    Meanwhile Jeff was working on the Sniper. The Sniper has a lot going on because it controls timing, breaks the coil for ignition, it needs to know about the AC, it controls the fan, and of course all of this is done properly with relays and so on. He did a great job tidying that wiring harness up so it looks factory.














    Meanwhile on the inside the HVAC got permanently mounted and the wiring all tidied up there too. Lots o wire, all brand new.








    And, after we got the Sniper in, engine harness, and chassis power/grounds we checked everything and it was good. The final check came with hooking the column up, ignition switch, and firing the Sniper up. It lives!!






  10. #60

    Default

    Glad you got it fired up!

    my adjustable proportioning valve is in the exact same spot!

  11. #61

    Default

    The engine hasn't been fired yet, but, we're not that far away either. For sure we'll have video of that!

Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •