Has anyone tried the moldings out yet? i was curious on fitment weather or not they are the same size and length. thanks
Has anyone tried the moldings out yet? i was curious on fitment weather or not they are the same size and length. thanks
1983 Mustang gt-t-tops,5.0,4spd,all original
1983 Mustang GT -sunroof 5.0 5sp, work in progress.
2003 Cobra - 2.8 pulley, headers, o/r xpipe,flowmaster cat back, bf irs brace, h&r race springs, mmcc. SOLD
2002 Mustang GT - Lt headers,o/r hpipe,slp2 catback,4.10 gears,cai, pro 5.0 shifter,sct2 tune. SOLD
2001 Focus zx3 - Daily Driver
1988 Bronco XLT - 5.0 -Sold
1983 Mustang GT - (my first car) sunroof, 306,srod 4sp, 3.55 gears, Lt headers, o/r hpipe, flowmaster catback. SOLD
Used them on my Pace Car......
Very happy with them......
I purchased two sets. Used one set for the door mlds, and cut up the other set to make new mlds for the back of the fenders and the front of the quarter panels.
I bought them but havenīt installed them yet, I measured them by just placing it over the door and they seemed to be about 1/2" short but I know these need to be heated and stretched a bit to install them.
Quality looks very good
1979 Mustang Cobra 5.0
2P Red and 1C Black
Stock never goes out of style
MCA #70281 - 79-93 MCA Concours Judge
Proverbs 3:5-6
My Mustang Story
http://vb.foureyedpride.com/showthre...71#post1688371
I'll take some photos this weekend as I will have the car out...at the Mustang & Ford show in Louisville KY.
Currently I just used stripe tape all the around...(kind of ran out of time trying to get all together for the Mustang club show in Indy back in Sept.
If you remember I had to take care of the rear bumper issue at the last minute....)
Cool, thanks! Looking forward to the pictures.
1979 Mustang Cobra 5.0
2P Red and 1C Black
Stock never goes out of style
MCA #70281 - 79-93 MCA Concours Judge
Proverbs 3:5-6
My Mustang Story
http://vb.foureyedpride.com/showthre...71#post1688371
And where are you sourcing these ?
clowns to the left of me , Jokers to the right
Attached are photos of my Pace Car at a show this weekend......I think the Mlds appear close to the OEM's
Granted, there are a few minor differences......the pinstripe area is inset for stripe tape.
But I think it would take someone with a lot of knowledge about the mlds to see the differences.......
Looks great I was hoping to see them in person at foxtober fest.
How was the length and height compared to factory? the reason im asking is when i had my car painted i did not take moldings off i had them taped off so if the new ones are any smaller you will see a paint line around them on my car. bigger would be better for me. thanks
1983 Mustang gt-t-tops,5.0,4spd,all original
1983 Mustang GT -sunroof 5.0 5sp, work in progress.
2003 Cobra - 2.8 pulley, headers, o/r xpipe,flowmaster cat back, bf irs brace, h&r race springs, mmcc. SOLD
2002 Mustang GT - Lt headers,o/r hpipe,slp2 catback,4.10 gears,cai, pro 5.0 shifter,sct2 tune. SOLD
2001 Focus zx3 - Daily Driver
1988 Bronco XLT - 5.0 -Sold
1983 Mustang GT - (my first car) sunroof, 306,srod 4sp, 3.55 gears, Lt headers, o/r hpipe, flowmaster catback. SOLD
As for the door mld, I have had my originals off for so long that I can't make a judgment as to the length.But appears to be correct with space in the front for the opening of the door and gap at the end to match the gaps on the other panels.
And I cut the extra one to the length of the old side mlds for the front of the qrt and the rear of the fenders
If you have painted your car with the mlds attached I have a feeling you are going to run into more of an issue than just length......
Most likely you are going to have a peeling paint problem around the edges of the old mlds.....
No matter how close you try and sand/prep next to an item that is left on a car there is always a very good possibility that you missed a spot and you are not going to have a mechanical bond of the paint to the surface, or you will have "bridging" of the paint to the mld.
Double post...sorry
Where did you get the mouldings I ask ya
clowns to the left of me , Jokers to the right
Fox Mustang Restoration has them:
http://www.foxresto.com/category-s/2435.htm
Late Model Restoration also has them:
https://lmr.com/products/79-93-Musta...ngs-Kits#14988
Made by Daniel Carpenter (DCM). FMR and LMR are just re-sellers but that's what you have to do because DCM only sells wholesale.
Axle Tag Decoder
Buck Tag Decoder
Door Tag Decoder
Owner Card Decoder
Transmission Tag Decoder
VIN Decoder
FEP Registries: Black Magic & Crimson Cat / Cobra / Dominator / G.T.350 / LTD LX/Police & Marquis LTS / M81 / Pace Car / Predator / Saleen / Turbo GT & Turbo RS / Twister II
Wanted (Dead or Alive): VINs, door tags, buck tags, build sheets, window stickers, owner cards, transmission tags, axle tags
1979 Mustang Cobra 5.0
2P Red and 1C Black
Stock never goes out of style
MCA #70281 - 79-93 MCA Concours Judge
Proverbs 3:5-6
My Mustang Story
http://vb.foureyedpride.com/showthre...71#post1688371
Thanks for the complement......
About 95% there........still need to address a couple of items......
But, as most folks on this site know......."it's never done"
It looks like you used NOS Emblems or did you shorten this?
Usually the 79 is on the Lip of the rear fender for aftermarket.
Here is a post where we talked about this
http://vb.foureyedpride.com/showthre...ace+car+decals
Last edited by 79mustangcobra; 10-21-2016 at 12:30 PM.
1979 Mustang Cobra 5.0
2P Red and 1C Black
Stock never goes out of style
MCA #70281 - 79-93 MCA Concours Judge
Proverbs 3:5-6
My Mustang Story
http://vb.foureyedpride.com/showthre...71#post1688371
I also notice some of the decals in that thread (for the date) are red and some are orange....which is correct?
Jason Smith
MCA #65481
'82 Capri RS Resto-Mod
'88 #400 Saleen Coupe "Mean Machine" Legal Guardian
'93 LX Yellow/Black Summer Feature - 2,800 Mile Original Survivor (Foxtoberfest 2019 Best Original 87-93)
'05 S-281 Mineral Grey
Now I have to go out in the shop and pull off the car cover to answer your question........
The line below "official pace car" is red, just like the outlining of "official pace car"
If the bottom line looks orange anywhere it must just be the lighting in the photo.......
Thank you for the source.
Too bad all you can get is the 2 door mouldings
Last edited by ashley roachclip; 10-22-2016 at 12:11 AM.
clowns to the left of me , Jokers to the right
I used a Phoenix graphics kit I bought over 15 years ago
I will give up one secret........after looking at Steve's unrestored car.....
The horse colors on this old kit are mixed up....
But I think I have found a cure for this issue
Connect With Us