exhaust tip for the anni

[emerygt350]

Any suggestions? I can't find anything that even remotely resembles the original. I had to swap it out before it fell off and killed somebody.

[smitty54]

This is what I'm using. It's pretty close to the original.
http://www.ebay.com/itm/Exhaust-Tip-...tT238x&vxp=mtr

[conmech]

Mike and I discussed the exhaust for my turbo 4 (not sure of your set up but could apply). Designed as a better breathing set up, off the Magnaflow hi flow C.A.R.B. approved cat, the exhaust splits and runs out opposite sides of the fuel tank. LX tips, I believe, complete the look.

[TopGear85]

I like the one Smitty posted. It's very close to original and about the best you're gonna find (with the look of the original). I'd go with that.

[emerygt350]

those duals look great but i plan on keeping the single for the time being. i have duals sitting in the garage but just not ready to break from stock. smitty's look perfect.

[emerygt350]

smitty, that is a weld on right?

[9D83]

Smittys looks pretty dang close tho I seemed to remember my factory replacement one-installed circa'93-as being one piece up to the muffler. As I was in the garage organising stuff and drinking a beer (well, mostly drinking a beer)I took this of mine. Sure enough there's a weld...

[smitty54]

smitty, that is a weld on right?

Yes, It's a weld on.

[emerygt350]

Excellent. Buying one now...

[sowaxeman]

Good call....not sure you can get any closer without dropping big money on a NOS complete rear tailpipe assemble, assuming you could find one.

[Gemini1999]

Stinger also sells a dual outlet tip for about 50 bucks.

[emerygt350]

I looked at the stinger but it wasn't quite right and I couldn't find a website that actually sold it. It is like the company disappeared...

[Gemini1999]

I looked at the stinger but it wasn't quite right and I couldn't find a website that actually sold it. It is like the company disappeared...

The website is still active and the part is at the bottom of this page:

http://www.stinger-performance.com/stockparts.html

[JTurbo]

I bought a similar dual chrome tip off ebay for use on my 82. Plan on welding it to a standard {shortened} 2-1/4" LX style tail pipe....

[emerygt350]

wow, several months ago every time I tried to follow a stinger link it was all dead. That looks good and nearly identical to the ebay part.

[84GT350_Annv]

I popped for the one Smitty proposed also. Will post a pic once it gets installed.

[emerygt350]

Just had the new tip welded. Very nice. I had them tuck it under just a little more than Smitty's tip. Looks great and the sound is unchanged as far as I can tell. Guys did a good job sneaking it in there for 30 dollars. Was not easy with the tank so close.

[JTurbo]

Looks great!

[homer302]

Stinger:

[emerygt350]

the stinger looks great. they had to cut mine up a bit since the straight pipe they had in there already didn't really work with that bent initial part. I also have 2.25 " pipes which they had to work with. THey ended up cutting the tip at an angle where it joined so they ended up with an equal diameter for the weld. I will try to get a better picture up close tomorrow.

[84GT350_Annv]

Got the tip Smitty recommend installed yesterday. The fella struggled with it for a while but I think it turned out well. He also cut out and replaced some crap between the CAT and the muffler.

[84GT350_Annv]

Not sure what happened to the picture it was there earlier. I'll try to replace it later.

[tulsa]

Got the tip Smitty recommend installed yesterday. The fella struggled with it for a while but I think it turned out well. He also cut out and replaced some crap between the CAT and the muffler.

id be very happy with that ..

[emerygt350]

I think the only difference from the original is the distance between the pipes is maybe a 1/2 inch greater with the new one. Nothing I am going to complain about.