Activity Stream

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Blog Blogs Groups Groups

Yesterday, 10:43 PM

Jerry peachuer replied to a thread Weld/braze aluminum radiator? in General BS

Maybe that liquid metal 2 part stuff It says you can drill and tap it Haven't used it but I see it on the counter at parts stores Does your...

12 replies | 346 view(s)

Yesterday, 10:22 PM

WILWAXU replied to a thread door window run channel? in Body Shop

I replaced the window channels, dew wipes, and weatherstripping on my '86 with parts from LMR. Removing the old crunchy window channels was the...

12 replies | 166 view(s)

Yesterday, 09:52 PM

Basin Motorsports started a thread FS: 1979-1984 Complete Set of Trim Moldings in Parts - For Sale & Trade

I have a complete set of trim moldings from my '80. Doors, fenders, and quarter panels. Should fit 1979-1984 models. $250 shipped. They have been...

0 replies | 17 view(s)

Yesterday, 09:49 PM

FB71 replied to a thread Radio chassis (?) reference in Audio and Electronic Accessories

Sam's PhotoFact manuals. Used to use them when I did TV/VCR repair...

3 replies | 135 view(s)

Yesterday, 09:44 PM

Basin Motorsports started a thread FS: Maximum Motorsports 79-04 Hardtop Rollbar in Parts - For Sale & Trade

I have an MM rollbar (79-04 hardtop) still in its packaging. Bought in November 2019, and never unpacked it. It has the fixed harness bar with the...

0 replies | 15 view(s)

Yesterday, 07:12 PM

xctasy replied to a thread CFI to EFI in V8 Powertrain & Accessories

True that. Check with emerygt350 and fgross2006 and MattyJ The stock CFi HO 5.0 did, has done and always will. Kic|< A$$. Carrol Shelby started...

5 replies | 110 view(s)

Yesterday, 03:11 PM

richpet replied to a thread Weld/braze aluminum radiator? in General BS

I have one of those in the Granada for a mechanical water temp gauge. Easy to install, but it is tough to disguise. Sent from my Pixel 3 XL using...

12 replies | 346 view(s)

Yesterday, 01:15 PM

KevinK replied to a thread Radio chassis (?) reference in Audio and Electronic Accessories

I have seen some Ford radio service manuals. They may reference some chassis numbers but it really comes down to getting the internal parts to make...

3 replies | 135 view(s)

Yesterday, 01:10 PM

KevinK replied to a thread CFI to EFI in V8 Powertrain & Accessories

Not sure where your mechanic gets his info. There are only a few parts to replace on CFI. Injectors would be the main concern. They can be rebuilt or...

5 replies | 110 view(s)

Yesterday, 12:53 PM

tbirdman replied to a thread Radio chassis (?) reference in Audio and Electronic Accessories

Looks like a website for factory service manuals for electronics. I found some part numbers for factory radios in there, but they list part numbers...

3 replies | 135 view(s)

Yesterday, 12:26 PM

richpet replied to a thread Finally running right! in Online Car Show/Show & Tell

Weather is supposed to be good tomorrow here and at the coast. That means road trip over the mountains for lunch in Florence! It will be a good 140...

15 replies | 662 view(s)

Yesterday, 12:22 PM

richpet replied to a thread Ridge reamer. Is it necessary? in V8 Powertrain & Accessories

Or pull the pistons out the bottom of the block. Installing them could then be an issue if the ridge is too much. Hate to say it, but $70 (or less...

3 replies | 137 view(s)

Yesterday, 12:17 PM

richpet replied to a thread FS: Assorted parts in Parts - For Sale & Trade

Shauncb- if you're talking about the MM 2-point brace a fella expressed interest. Waiting to hear back from him and will let you know. I know it...

17 replies | 1001 view(s)