Activity Stream

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Blog Blogs Groups Groups

Today, 07:55 AM

David Claflin replied to a thread 1986 GT Project in General Tech

A 26x10 slick will work better than that M/T ET street. That's a 27" tire, and a slick is way more forgiving to not so great track surfaces, and...

20 replies | 1019 view(s)

Today, 07:51 AM

Jerry peachuer replied to a thread Weld/braze aluminum radiator? in General BS

Jb weld weld steel stick is what I was referring to above Because its not only thin its underpressure is where the concern is

13 replies | 370 view(s)

Today, 06:32 AM

BoostMasterZero replied to a thread Is it possible to wire Bluetooth to the OEM radio? in Electrical

I get that, and can vouch for my Dad being one of those type of guys. He needs hearing aids and watches TV at his home with my Mom that is...

13 replies | 382 view(s)

Yesterday, 10:43 PM

Jerry peachuer replied to a thread Weld/braze aluminum radiator? in General BS

Maybe that liquid metal 2 part stuff It says you can drill and tap it Haven't used it but I see it on the counter at parts stores Does your...

13 replies | 370 view(s)

Yesterday, 10:22 PM

WILWAXU replied to a thread door window run channel? in Body Shop

I replaced the window channels, dew wipes, and weatherstripping on my '86 with parts from LMR. Removing the old crunchy window channels was the...

12 replies | 173 view(s)

Yesterday, 09:52 PM

Basin Motorsports started a thread FS: 1979-1984 Complete Set of Trim Moldings in Parts - For Sale & Trade

I have a complete set of trim moldings from my '80. Doors, fenders, and quarter panels. Should fit 1979-1984 models. $250 shipped. They have been...

0 replies | 23 view(s)

Yesterday, 09:49 PM

FB71 replied to a thread Radio chassis (?) reference in Audio and Electronic Accessories

Sam's PhotoFact manuals. Used to use them when I did TV/VCR repair...

3 replies | 142 view(s)

Yesterday, 09:44 PM

Basin Motorsports started a thread FS: Maximum Motorsports 79-04 Hardtop Rollbar in Parts - For Sale & Trade

I have an MM rollbar (79-04 hardtop) still in its packaging. Bought in November 2019, and never unpacked it. It has the fixed harness bar with the...

0 replies | 20 view(s)

Yesterday, 07:12 PM

xctasy replied to a thread CFI to EFI in V8 Powertrain & Accessories

True that. Check with emerygt350 and fgross2006 and MattyJ The stock CFi HO 5.0 did, has done and always will. Kic|< A$$. Carrol Shelby started...

5 replies | 116 view(s)

Yesterday, 03:11 PM

richpet replied to a thread Weld/braze aluminum radiator? in General BS

I have one of those in the Granada for a mechanical water temp gauge. Easy to install, but it is tough to disguise. Sent from my Pixel 3 XL using...

13 replies | 370 view(s)

Yesterday, 01:15 PM

KevinK replied to a thread Radio chassis (?) reference in Audio and Electronic Accessories

I have seen some Ford radio service manuals. They may reference some chassis numbers but it really comes down to getting the internal parts to make...

3 replies | 142 view(s)

Yesterday, 01:10 PM

KevinK replied to a thread CFI to EFI in V8 Powertrain & Accessories

Not sure where your mechanic gets his info. There are only a few parts to replace on CFI. Injectors would be the main concern. They can be rebuilt or...

5 replies | 116 view(s)

Yesterday, 12:53 PM

tbirdman replied to a thread Radio chassis (?) reference in Audio and Electronic Accessories

Looks like a website for factory service manuals for electronics. I found some part numbers for factory radios in there, but they list part numbers...

3 replies | 142 view(s)

Yesterday, 12:26 PM

richpet replied to a thread Finally running right! in Online Car Show/Show & Tell

Weather is supposed to be good tomorrow here and at the coast. That means road trip over the mountains for lunch in Florence! It will be a good 140...

15 replies | 663 view(s)

Yesterday, 12:22 PM

richpet replied to a thread Ridge reamer. Is it necessary? in V8 Powertrain & Accessories

Or pull the pistons out the bottom of the block. Installing them could then be an issue if the ridge is too much. Hate to say it, but $70 (or less...

3 replies | 141 view(s)

Yesterday, 12:17 PM

richpet replied to a thread FS: Assorted parts in Parts - For Sale & Trade

Shauncb- if you're talking about the MM 2-point brace a fella expressed interest. Waiting to hear back from him and will let you know. I know it...

17 replies | 1002 view(s)